ipr press head — datasheet

ipr300hP-60

Article no.: 150149
Werkzeugfinder Download as PDF
Technical data
Pressing force
300 kN
Operating pressure
850 bar
Max DIN size
44
Available crimp widths
14, 17, 25, 40 mm *
Max cross-section
625 mm²
Fork inner Ø
60 mm
Dimensions
Ø 90 x 305
Weight
5.2 kg

* The crimp width depends on the specific press insert — see table below.

Build
Recommended drives
Accessories
Special features
Compatible press inserts

29 press inserts are compatible with this press head (DIN size ≤ 44).

Designation KZ Press width mm Cu mm² Al mm² Al/St Aldrey
SK 10 10 14
25
tension-resistant:
25
— — —
SK 12 12 14
35
tension-resistant:
35
16 - 25
tension-resistant:
16 - 25
Alu sleeve:
16/2,5 25/4
25
SK 13 13 14 — —
Steel sleeve:
120/20 150/25 70/23 132/17 Leopard 120/25 120/15 125/25 152/25 Ostrich 190/18 224/20 239/23 259/23 Groningen 381/20 476/24
—
SK 14 14 14
50
tension-resistant:
50
35
tension-resistant:
35
Alu sleeve:
35/6
35
SK 15 15 14 — —
Steel sleeve:
44/32 50/30 125/30 170/40 185/30 210/35 230/30 240/40 265/35 305/40 340/30 385/35 450/40 495/35 570/40 147/34 152/35,5 Piper 158/37 Wolf 191/31 242/32 242/39,5 Hawk 423/37
—
SK 16 16 14
70
tension-resistant:
70
50
tension-resistant:
50
Alu sleeve:
50/8
50
SK 17 17 14 — —
Steel sleeve:
210/50 300/50 380/50 510/45 560/50 650/45 74/43 Horse 120/42 184/43 Lynx 185/43 193/45 282/46 Dove 293/48 381/49 Bison
—
SK 18 18 14
95
70
tension-resistant:
70
Alu sleeve:
70/12
70
SK 19 19 14 — —
Steel sleeve:
95/55 435/55 97/56 Dorking 237/56 Lion 242/56 Hen 403/52 Condor 415/54 428/56 Zebra 537/53
—
SK 20 20 14
120
tension-resistant:
95
— —
95
SK 21 21 14 — —
Steel sleeve:
105/75 120/70 490/65 550/70 565/72 101/72 185/62 265/62 Bear 360/60 403/65 Drake 456/59 Canary 524/68
—
SK 22 22 14
150
tension-resistant:
120
95 - 120
tension-resistant:
95
Alu sleeve:
95/15
—
SK 22B 22 40 — — — —
SK 23 23 14 — —
Steel sleeve:
680/85
—
SK 25 25 14
185
tension-resistant:
150
150
tension-resistant:
120
Alu sleeve:
44/32 50/30 120/20
120
SK 25B 25 40 — — — —
SK 28 28 14 — —
Alu sleeve:
125/30 150/25
Steel sleeve:
340/110
—
SK 28B 28 40 — — —
150 - 185
SK 30 30 17
tension-resistant:
185
—
Alu sleeve:
95/55 170/40 185/30
—
SK 30B 30 25 — — — —
SK 32 32 17 — — — —
SK 32B 32 25 — — — —
SK 34 34 17
tension-resistant:
240
300
tension-resistant:
240
Alu sleeve:
105/75 120/70 210/35 210/50 230/30 240/40
—
SK 34B 34 25 — — — —
SK 38 38 17
400
400
tension-resistant:
300
Alu sleeve:
265/35 300/50 305/40 340/30
—
SK 38B 38 25 — — — —
SK 42 42 17
500
—
Alu sleeve:
380/50 385/35
—
SK 42B 42 25 — — — —
SK 44 44 17
625
500
— —
Cu / Al columns: tension-relieved / tension-resistant. The list shows all tool sizes approved for this press head.

Safety notice: Before use, please ensure that the correct press insert is used with the appropriate tool and material. Please refer to the tables. For any questions or discrepancies, please contact ipr werkzeuge.

Press insert holders
Notes & FAQ
For all tools

Occasionally air in a hydraulic tool prevents it from working at full capability. The question is: how does the air get into the system? Please note the following: • After the hydraulic power unit's tank has been fully emptied and then refilled, the tank must be bled. • New hoses must be filled with oil before use. The same applies after hose testing. • If the nipples on the tool are replaced in-house, it is essential that whoever does so has first been instructed in bleeding the tool: when the fitted nipple is removed, the oil drains out and the oil chamber fills with air.
View all notes